S2K Commerce - Products Dropdown
ActionsS2K Commerce - Shopping Cart
ActionsS2K Commerce - Order Entry
ActionsAltronix T3MK77F16D Trove Mercury kit is pre-assembled and consists of Trove enclosure with factory installed Altronix power supply/chargers and sub-assemblies. This kit accommodates various combinations of Mercury boards for up to sixteen (16) doors in a single enclosure.
- Input: 120VAC 60Hz/9.0A.
- Output:
- 24VDC @ 9.2A max current.
- Sixteen (16) Fail-Safe/Fail-Secure or Dry Form "C" Outputs
- Fully assembled kit includes:
- Trove3 enclosure with TM3 backplane
- Two (2) eFlow104NB - Power Supply/Chargers
- Two (2) ACM8CB - PTC Protected Access Power Controllers
- Two (2) PD8ULCB - PTC Protected Power Distribution Modules
- One (1) RSB2 - Rocker Switch Bracket with Two (2) Rocker Switches
- Back-up Battery:
- Capacity: 12AH / 12VDC (Up to 4 within enclosure); 40 AH / 65 AH (requires separate enclosure).
- Type - Sealed lead acid or gel type.
- Fuse Rating: 15A/32V
- Failover - Upon AC loss, instantaneous.
- Supervision:
- AC Failure - Form "C" contacts.
- Battery - Form "C" contacts.
- Low DC Power Shutdown - Shuts down DC output terminals if battery voltage drops below 71-73% for 12V units and 70-75% for 24V units (depending on the power supply). Prevents deep battery discharge.
- LED Indicators:
- Input - 120VAC is present.
- DC Output - Powered.
- Battery - Discharged or not connected.
- Faceplate
- 501LTE and 502 circuit boards
- 4G LTE antenna
- PS-12DC1 power supply
Reliable, durable and highly accurate ZK fingerprint sensor with ver. 10 algorithm provides less than 1.5 second user recognition. Works without computer. Complete setup and programming can be done via keypads and embedded firmware.Audio-Visual Indication for acceptance and rejection of valid/invalid fingerprints. Relay Outputs for electric lock and alarm. Inputs for door status sensor and exit switch. Supports multiple timezones and personnel groups for programming valid entry zones. IP65 rated waterproof enclosure permits this reader to be used for outdoor applications.
Can store up to 3000 fingerprint templates, 10,000 cards and 50000 transactions. The data can be backed up to a USB drive and transferred to another reader in the absence of computer connectivity. Internal Proximity Card or Mifare Card reader allows dual factor authentication for access control.
Features
- Rugged structure for outdoor installation and extra durability
- IP65 rated waterproof and weatherproof structure
- Slim and elegant design
- One of the worlds smallest fingerprint terminals
- Sleek and slim design for narrow spaces.
- Fast and accurate fingerprint algorithm
- Fingerprint identification in 1 second
- Stores 3000 fingerprint templates, 10,000 cards and 50000 transactions
- Easy installation and connectivity with Wiegand input and output and network interface by TCP/IP and RS485
- Full access control features include DLST, Web-server, Anti-Passback and access control interface for third party electric lock, door sensor, exit button and alarm
- Easy operation and management; works without computer and has built-in keypad and RF card reader for multi-modal authentication
- Special Order with Mifare card module
Input
- Voltage: 120VAC, 60Hz.
- Fusing: 5A / 250V.
Output
- Voltage: 24VDC.
- Current: 4A continuous.
- Other: Overvoltage protection. Filtered and regulated.
- Capacity: 7AH / 12VDC (Up to 2 within enclosure). 40 AH / 65 AH (requires separate enclosure).
- Type: Sealed lead acid or gel type.
- Fuse: Rating 10A/32V.
- Failover: Upon AC loss, instantaneous.
- AC Failure: Form “C” contacts.
- Battery: Form “C” contacts.
- Low DC Power Shutdown: Shuts down DC output terminals if battery voltage drops below 70-75% for 24V units (depending on the power supply). Prevents deep battery discharge.
- Input: 120VAC is present.
- DC Output: Powered.
- Battery: Discharged or not connected.
Input
- Voltage: 24VDC from eFlow4NB.
Output
- Voltage: 12VDC.
- Current: 6A continuous.
- Other: Surge suppression.
Indicators (LED)
- Input: 24VDC is present.
- Output: Powered.
Input
- Voltage: 24VDC from eFlow4NB.
- Fusing: 10A / 250V.
Output
- Voltage: 24VDC.
- Four (4) independently controlled 2.5A outputs:
- a) Four (4) Fail-Safe and/or Fail-Secure power outputs.
- b) Four (4) dry form “C” 5A rated relay outputs.
- c) Any combination of the above.
- Four (4) auxiliary power outputs (unswitched).
Outputs Ratings
- Fuses: 3A / 32VDC.
Indicators (LED)
- Red LEDs: Outputs are triggered (relays energized).
- Green LED: FACP disconnect is triggered.
Input
- Voltage: 12VDC from VR6 and 24VDC from eFlow4NB.
- Main Fuse Rating: 10A.
Output
- Voltage: 12VDC and/or 24VDC.
- Any of the eight (8) fuse protected power outputs are selectable to follow power Input 1 or Input 2.
- Individual outputs may be set to OFF position for servicing.
Outputs Ratings
- Fuses: 3A / 250V.
Indicators (LED)
- DC Output: Eight (8) individual output LEDs.
- CI-CP1 is supplied with a 20' cord and pull handle. Ceiling mount
- Interior or exterior use
- Heavy duty die cast aluminum enclosure
- NEMA 1 and NEMA 2 rated for interior use
- NEMA 4 rated for exterior use
- Optional 110V heater (WPS1)
- 3 Buttons for OPEN, CLOSE and STOP
- High Power Output Contacts, 5A/10A @ 240 VAC
- NEMA 1 for Indoor use
- Surface or Flush Mount
- 3 Buttons for OPEN, CLOSE and STOP
- High Power Output Contacts, 5A/10A @ 240 VAC
- NEMA 1 for Indoor use
- Surface or Flush Mount
- CI-WPS1 is ideal for activating industrial doors or use by lift truck operators.
- CI-WPS1 may be ceiling or wall mounted
- Interior or exterior use
- Heavy duty die cast aluminum enclosure
- NEMA 1 and NEMA 2 rated for interior use
- NEMA 4 rated for exterior use
- 110V heater
- CI-WPS1 is ideal for activating industrial doors or use by lift truck operators.
- CI-WPS1 may be ceiling or wall mounted
- Interior or exterior use
- Heavy duty die cast aluminum enclosure
- NEMA 1 and NEMA 2 rated for interior use
- NEMA 4 rated for exterior use
- Optional 110V heater
- 3 Buttons for OPEN, CLOSE and STOP
- Key Lockout Available
- NEMA 4 Enclosure for Outdoor Use
- Wiegand or RS-485 Interface to Reder
- TCP/IP to PC, Support for WAN Communication
- Touch Keyboard and LCD display
- Supports 30,000 Valid Cards and 150,000 Events
- Supports Card, Password, Fingerprint and a Combination of Credentials
- Add Devices in SmartPSS via P2P Connection
- Door Time Out, Intrusion, Duress and Tamper Alarms
- Anti-passback and Multi-card Open Options
- Supports 128 Efficient Time and Holiday Schedules
- Supports TCP/IP, Wi-Fi Communication, and eHome Protocols
- Maximum 32 GB, built-in microSD card
- Mifare card
- Door magnetic sensor 1, alarm input 2, tamper-resistant switch 1, exit button x 1
- 12 VDC/1 A
- -40° to 140° F (-40° to 60° C)
- 10% to 90% (no--condensing)
- 8.58" × 3.07" × 1.61" (218 mm × 78 mm × 41 mm)