|◀ 1 - 12 of 146 ▶|
View:
You must be logged in to order this item. Log in here
You must be logged in to order this item. Log in here
You must be logged in to order this item. Log in here

The DTK-2MHLP24B provides surge protection for two 24V alarm system loop circuits in a field-replaceable module. With required snap-track bases, protect up to 10 pairs with a common ground.

  • Protects two 24V pairs per module
  • Multi-stage SAD technology provides the best possible protection
  • Field-replaceable modular edge card connection with single point ground for fast installation
You must be logged in to order this item. Log in here

The DTK-2LVLPF protects 24V SLC loops on first generation fire alarm control panels, where surge protection and current limiting functionality are required.

  • Protects up to 2 pairs of SLC loop circuits
  • Low-current fusing prevents induced surges from damaging sensitive equipment
  • Series connection, parallel function adds no resistance to loop circuits

Item#:
DTK-2LVLPF
You must be logged in to order this item. Log in here
  • 120/240 VAC 50-60 Hz input
  • 5.1 Amps @ 120 VAC or 2.5 Amps @ 240 VAC
  • Battery Standby Current 75 mA
  • Alarm Standby Current 75 mA (no external load)
  • Terminals support 12 - 18 AWG wire.
Item#:
PSN-64
You must be logged in to order this item. Log in here
You must be logged in to order this item. Log in here
You must be logged in to order this item. Log in here

Altronix AL400ULACM converts a 115VAC 60Hz input into eight (8) independently controlled 12VDC or 24VDC Fail-Safe and/or Fail-Secure outputs with a total of 4A @ 12VDC or 3A @ 24VDC continuous supply current. Outputs are activated by an open collector sink or normally open (NO) dry trigger input from an Access Control System, Card Reader, Keypad, Push Button, PIR, etc. This unit will route power to a variety of access control hardware devices including Mag Locks, Electric Strikes, Magnetic Door Holders, etc. The outputs will operate in both Fail-Safe and/or Fail-Secure modes. This unit is designed to be powered by one common power source (factory installed) which will provide power for both the board operation and locking devices, or two (2) totally independent power sources, one (1) providing power for board operation and the other for lock / accessory power. The FACP Interface enables Emergency Egress, Alarm Monitoring, or may be used to trigger other auxiliary devices. The fire alarm disconnect feature is individually selectable for any or all of the eight (8) outputs.

Features

  • Fire Alarm disconnect (latching or non-latching) is individually selectable for any or all of the eight (8) outputs.
  • Fire Alarm disconnect input options:
  • a) Normally open (NO) or normally closed (NC) dry contact input.
  • b) Polarity reversal input from FACP signaling circuit.
  • Alarm output relay indicates that FACP input is triggered (form "C" contact rated @ 1A 28VDC not evaluated by UL).
  • Short circuit and thermal overload protection.

Item#:
AL400ULACM
You must be logged in to order this item. Log in here
You must be logged in to order this item. Log in here

10 AMP 120VAC REMOTE CHARGER POWER SUPPLY W/ METAL ENCLOSURE

This item has been discontinued and replaced by item 
The PS Series is a remote power supply line from Silent Knight and is a direct replacement
for the 5495/5499. The SK-PS6 is a 6 amp and the SK-PS10 is a 10 amp, remote power
supply with battery charger that may be connected to any 12 or 24 volt fire alarm control
panel (FACP) or used as a standalone power supply. The PS Series provides 24 VDC power
for NACs (notification appliance circuits) configured as either Class B or Class A (requires
the ZNAC-PS option card) with multiple sync protocol options. The PS Series also provides
auxiliary power, constant or resettable, suited for detectors, annunciators, door holders, and
other fire alarm system peripherals. The PS Series cabinet can hold two 7 AH or 18 AH
batteries and can charge up to 33 AH batteries in a separate cabinet.
You must be logged in to order this item. Log in here

The 5895XL intelligent power module is a 6 amp notification power expander that provides its own AC power connection, battery charging circuit, and backup battery for use with Silent Knight addressable fire alarm control panels. Six Flexput circuits can be programmed as notification appliance circuits, conventional initiation circuit, or auxiliary power for constant, resettable or door holder power. The 5895XL also provides a conditioned SBUS circuit allowing up to an additional 6,000 feet of wiring for SBUS devices.

Features

  • 6A output power
  • Six Flexput circuits rated at 3A each can be programmed as notification appliance circuits, auxiliary power, or initiation circuits
  • Supports Class A configuration for SBUS and Flexput circuits
  • Each output individually mapped through fire alarm control panel programming
  • Two form C programmable relays rated at 2.5A at 24VDC
  • SBUS repeater conditions the RS-485 signal
  • Room in cabinet to mount two 5815XL SLC expanders
  • Built-in synchronization for appliances from AMSECO, Gentex, Faraday, System Sensor, and Wheelock
  • UL listed

Item#:
005895XL
You must be logged in to order this item. Log in here
|◀ 1 - 12 of 146 ▶|
View:
(Denotes required field.)