S2K Commerce - Products Dropdown
ActionsS2K Commerce - Shopping Cart
ActionsS2K Commerce - Order Entry
Actions
You must be logged in to order this item.
Log in here
Item#:
PRM-2WC
You must be logged in to order this item.
Log in here
Item#:
IQP4STAND-WHT
You must be logged in to order this item.
Log in here
16 Zone hardwire to wireless translator with 319.5 MHz S-Line Encryption. Supports 2-Wire smoke detectors. Certified for Residential Fire. Installed in "Takeover" style enclosure. Built-In Power Supply, backup battery charging, and Relay for External Sirens or Speakers. Includes transformer.Â
The IQ Hardwire 16-F offers a cost effective way of integrating hardwired security & smoke detector zones with the IQ Panel 2/2+. It includes backup battery charging, 500mA of 12volt auxiliary power, an onboard siren relay, built-in status LED's for each zone and support for up to 10 two-wire smoke detectors. Normally Open and Normally Closed contacts are supported as well as powered zones like motion sensors and glass break detectors.
- Encrypted S-Line sensor technology protects signals sent to the IQ Panel while still providing support for legacy 319.5 systems
- Supports up to ten two wire smoke detectors
- LED lighted zones for ease of "learn-in" installation/troubleshooting
- EOL supervision using 4.7K Ohm resistors (included)
- Up to 500 Milliamps of power for hardwired motion detectors, glass break detector, and/or sirens
- Charging circuit for back-up battery, fully supervised with power outage recovery
Item#:
QS7133-840
You must be logged in to order this item.
Log in here
An "active" RS-485 data bus hub designed for jobs where an M1Gold or M1EZ8 Control is retrofitting an older panel that has multiple homerun 4 conductor keypad/data wires. It splits the main 485 data bus into 4 managed 485 branches. Each branch can have 2 parallel home run cables for a total of 8 home runs. The end of each cable is EOL terminated to insure proper operation and supervision.
Includes:
- ELK-M1DBHR Data Bus Hub
- ELK-SWG Circuit Board Mounting Glides
- Instructions
- Splits The Controls' RS-485 Data Bus Output Into 4 Managed Branches
- Each Managed Branch Can Have 2 Parallel Home Run Cables (Total Of 8 Home Runs)
- EOL Termination Of Each Branch Insures Proper Operation And Supervision
- Works With Std. 4 Conductor Home Run Wire
- An Additional Unit May Be Connected In Parallel To The Control For Expanding Total Capacity
- Includes Mounting Rails for ELK-SWB Boxes
- Inputs: Elevator Screw Terminals, 4 Position
- Output: Elevator Screw Terminals, 4 Position
- Circuit Board Dimensions: 4.9 in. x 2.75 in.
Item#:
M1DBHR
You must be logged in to order this item.
Log in here
Item#:
EXDL-0
You must be logged in to order this item.
Log in here
The ELK-RJSET is for use with Alarm System Communicators, Line Fault devices, or other equipment as a means of connecting to the incoming telephone line. Includes USOC RJ31X 8 pin modular surface mount jack and 2 ft. 8 wire modular cord with plug on one end and spade terminals on the other.
- USOC RJ31X 8 pin modular surface mount jack.
- Built-in pass through shorting bars when plug is removed.
- Connector pins are plated with 50 microns of gold.
- Includes self adhesive foam mounting pad.
- Packaged in a clear poly bag.
- 24 inch, 8 wire modular cord with plug on one end and spade terminals on the other.
- FCC approved - UL listed as a Communication Circuit Accessory
Item#:
RJSET-ELK
You must be logged in to order this item.
Log in here
Item#:
ACD-50
You must be logged in to order this item.
Log in here
Item#:
ADC-T40K-HD-W
You must be logged in to order this item.
Log in here
Item#:
BP-200F
You must be logged in to order this item.
Log in here
S2K Administration - Form Template Display
Actions
(Denotes required field.)