S2K Commerce - Products Dropdown
Actions
S2K Commerce - Shopping Cart
Actions
S2K Commerce - Order Entry
Actions
The RM-2 Relay Module is used as an end-of-line (EOL) power supervision module for 4-wire smoke detectors. The RM-2 is used with the Polarity Reversal Module PRM4W and DSC FSA-410 series smoke detectors. When the PRM-4W reverses polarity on the smoke detector loop to activate all smoke detector sounders, the RM-2 Relay will continue to operate normally (regardless of input power polarity). Refer to the PRM-2W/4W Polarity Reversal Module
Item#:
RM-2
You must be logged in to order this item.
Log in here
The M1XSLZW is a specialized Elk-M1 serial expander for connecting an M1 Control to Z-Wave enabled devices through a Leviton VRC0P+3 Z-Wave Serial Interface. Z-Wave is a wireless, low power, "mesh" network technology widely used for automating devices such as: Lights, Thermostats, Electronic Locks, etc. Z-Wave empowers devices to be remotely controlled from across the room or across the world with benefits such as energy savings, convenience, and comfort.
The VRC0P+3 is known as a Z-Wave Secondary Controller. It must be included as a permanent member of the Z-Wave network as its job is to maintain contact with all Z-Wave devices. It communicates via RS232 to the M1XSLZW which translates the protocol into the M1 control. This allows commands to be sent and received on the Z-Wave network.
- Activity/Status LED (Orange)
- Auto-Reset Hardware Watchdog Circuit
- Addressable (1-7) TYPE 5 Databus ID
- Connection to VRC0P+3: DB9M 9 Pin Port
- Connection to M1: Elevator Screw Terminals (4)
- Operating Voltage: 12 Volts D.C.
- Current Draw: 31mA
- Housing: 4.25" x 6.375" x 2.125"
- Circuit Board: 2.25" x 3.95"
Item#:
M1XSLZW
You must be logged in to order this item.
Log in here
Allows a proximity card or fob to be used with the ELK-M1KP and ELK-M1KPB Keypads to quickly arm, disarm, operate a door strike, etc. Ideal for higher security installations and as an alternative to remembering PIN codes. Plugs into back of the Keypad. Uses M1PRC cards or M1PRF fobs. Includes one prox card.
- Simple Plug-in Installation
- Compatible with Clamshell Style (Credit Card size) Proximity Cards (ELK-M1PRC)
- Compatible with Keychain Style Proximity Fobs (ELK-M1PRF)
- Low Current Draw
- Substitutes for User Code Pin Entry Reader Format: 26 bit Wiegand
- 5 Pin Plug-in Connector
- Operating Voltage: 5 VDC from Keypad
- Current Draw: ~20 mA.
- Size: 1.875" W x 1" H x .375" D
Item#:
M1PR
You must be logged in to order this item.
Log in here
You must be logged in to order this item.
Log in here
The ELK-M1XSP is a "3 in 1" product for additional serial ports and for integration with lighting systems and thermostats. Jumpers on the M1XSP select the appropriate application, connection, and protocol. Best of all, the M1XSP operates from the 4-wire (RS-485) M1 Keypad data bus, allowing RS-232 ports to be located long distances from the control. The M1 Gold and M1EZ8 support up to 7 M1XSPs. The communications baud rate is adjustable from 300 to 38,400 baud. The unit comes complete with cable and a black surface mountable housing.
- Adapts the M1 to various Lighting control products which use "serial" communications. I.E.,OnQ-ALC, PCS-UPB, Centralite, etc.
- Adapts HVAC Communicating Thermostats from RCS, Aprilaire, and HAI to the M1 Cross Platform Control
- Expands the RS-232 Serial Ports of the M1 Control
- Operates from the M1 Data Bus
- DIP Switch Address Settings
- Jumper Options and LED Diagnostic indicator
- On-Board EOL Bus Termination Jumper
- Flash Memory for Firmware Updating
- Maximum Expandable Ports (Units): 7
- Operating Voltage: 12 Volts D.C.
- Current Draw: 31mA
- Housing Dimensions: 4.375" x 3.0" x 1.125"
- Circuit Board Dimensions: 3.5" x 2.75"
Item#:
M1XSP
You must be logged in to order this item.
Log in here
Adds 16 hardwired zones (EOL resistor supervised) to the M1 Gold or M1EZ8 Controls. Operates from 4-wire data bus. Up to 12 of these can be used, increasing total zones (inputs) to 208.
Includes:
- 16 Zone Input Expander
- ELK-SWG Circuit Board Mounting Glides 2/pack
- 18 2200 Ohm Resistors
- Instructions
- 16 EOL Resistor Supervised Hardwire Zones
- Operates on the 4-Wire Data Bus
- DIP Switch Address Settings
- Flash Memory for Firmware Updating
- Plug-In Terminal Strips
- Status and Diagnostic LED
- On-Board EOL Bus Termination Jumper
- Vertical Mounting using ELK-SWG Glides(included)
- Inputs: Plug-In Terminals with Elevator Style Wire Clamps and Screws
- Operating Power Range: 9 to 14 VDC
- Current Draw: 65 mA
- Size: 6 in. x 3.25 in. x .75 in. H
Item#:
M1XIN
You must be logged in to order this item.
Log in here
S2K Administration - Form Template Display
Actions
(Denotes required field.)