S2K Commerce - Products Dropdown
Actions
S2K Commerce - Shopping Cart
Actions
S2K Commerce - Order Entry
Actions
The 2GIG Wireless Keypad is a wallmounted unit designed for use as a secondary keypad for the 2GIG security system.
- Arms system in STAY or AWAY mode
- Disarms system
- Fire and Panic emergency functions
- Lithium batteries
- Transmits 345 MHz
- ETL listed
Item#:
2GIG-PAD1-345
You must be logged in to order this item.
Log in here
- Tri-Mode environmental sensing:
- Flood, high and low temp
- Freeze – for furnace failure – Under 45 degrees F
- Overheat – for furnace runaway or air conditioning failure – Over 100 Degrees F
- 3 unique wireless IDs or Loops: one for each function
- Cover and wall tamper.
- 3-5x more range than competing "puck" style sensors.
- 8-10 year battery life on CR2032 battery.
- IP67 waterproof rating
- 2.43 x 2.48 x 1.17 inches
Item#:
RE118
You must be logged in to order this item.
Log in here
KEYPAD FEATURES:
• Full color easy-to-use touchscreen interface
• One-touch Home and Emergency navigation
• Access to all Z-Wave functionality
• Firmware upgradeable using all current firmware tools
• Screen and buttons darken completely when not in use
and wake with a simple touch
Item#:
2GIG-TS2-E
You must be logged in to order this item.
Log in here
This item has been discontinued and replaced by item
PGP9986
The PG9985 is a fully supervised two-way wireless PowerG flood detector consisting of a probe connected to the device via a 1.8m (6ft) cable. The PG9985 senses the presence of water prompting advance warning of potential flooding. The transmitter is installed at a higher level on the wall with the probe located at floor level or a desired height. In the event that there is a water leak, the probe will detect the moisture and deliver the information to the transmitter.
The PG9985 PowerG Flood Detector is equipped with a visible link quality LED indicator that lets the installer choose the optimal location for installation, eliminating the effort of going back and forth to the keypad.
The flood probe of the PG9985 is also supervised to provide an alert upon a probe disconnection. This enhanced feature ensures that the device probe will be operational when it matters most.
Features
- Visible signal quality shown on the device
- Fully supervised
- 6 foot wire water probe
- Visible and transmitted low battery indication
- Prolonged battery life (8 years with typical use)
- Dimensions: 81 x 34 x 25mm (3.19 x 1.25 x 1in)
- Certified with ULC Wireless Commercial Burglary Listing under ULC-S304-16 Standard
Item#:
PG9985
You must be logged in to order this item.
Log in here
A bulky home security system can be an eyesore. Adding to that stress is hard wire installation permanently altering the aesthetics of a room, door or window treatment. With its wireless connectivity and fully concealed platform, however, the Ion Security Plunger is a door security sensor that finally eliminates these pesky inconveniences.
Features:
Item#:
PLUNGER-G
You must be logged in to order this item.
Log in here
The ELK-M1XEP is an Ethernet Appliance with a RS-232 Serial Port Interface. It may be used to connect a control in the M1 Family to an Ethernet network. It features email event notification and FIPS compliant encryption algorithms for security sensitive environments. It is powered by an ELK-P1216 12 Volts DC, 1.5 Amp plug-in power supply/adapter. A software setup utility is built into ElkRP for configuring the connection setup, network password, etc. The M1 Ethernet Interface is factory defaulted to obtain a dynamic IP address from a DHCP server (i.e. router, cable modem, etc.). It may optionally be setup with a static IP address.
Includes:
- M1 Ethernet Interface
- Plastic Housing
- 4 #6 Plastic Anchors
- 4 #6 Pan Head Sheet Metal Screws
- ELK-P1216 1.6A, 12Vdc Power Supply
- ELK-W040A DB9 Pin Serial Cable Assembly
- Instructions
- Secure connection with password protection and SSL/TLS encryption
- Flash Memory for Firmware Updating
- Event notification via E-Mail (SMTP)
- Supports automatic Dynamic DNS Updates with providers using the DynDNS protocol.
- Supports Network Time Protocol for synchronizing the M1/EZ8's clock with an Internet time server.
- Internet Monitoring and Reporting Capability
- Network stack supporting the following protocols:
- TCP,UDP,DHCP,SSL/TLS, NTP, SMTP
- Federal Information Processing Standards (FIPS) 128 bit encryption
- Integrated 802.3 compliant 10/100 Mbit network interface
- RS232, DB9M 9-pin serial port connection
- Connects to the M1 RS-232 Serial port (Port 0). The baud rate for this port must be set to 115,200 (factory default)
- RJ45 8-pin Network Jack
- 2.1mm barrel type power connector (center positive)
- LED Indicators for Power, Link, and Data
- Operating Voltage: 12 Volts D.C. from Elk-P1216 Plug-in Power Supply **
- Current Draw: approx. 300 mA
- Housing Dimensions: 4.25 in. x 6.375 in. x 2.125 in.
- Circuit Board Dimensions: 2.25 in. x 3.95 in.
- ELK-W040A Serial Ribbon Cable included
Item#:
M1XEP
You must be logged in to order this item.
Log in here
Features:
- Touchless convenience Integrated face recognition and Bluetooth technologies significantly streamline operation
- Sleek, thin design is easy-to-use with updated and intuitive UI providing one button access to smart home functions
- Live view video - cameras and doorbell cameras work with the 2GIG EDGE panel, with up to 8 different camera feeds viewable directly from the panel, view 4 camera feeds at a time
- Z-Wave 700 series supports large ecosystem of devices
- Superb audio quality with twice the speakers, double the microphones, added noise and echo cancellation with two-way communication
- Voice control through Google Assistant, Amazon Echo and Siri Shortcuts
- Ability to customize with controls, rules, scenes, and notifications
- Compatible with eSeries encrypted sensors
- Alarm.com compatible
Item#:
2GIG-EDG-NA-VA
You must be logged in to order this item.
Log in here
You must be logged in to order this item.
Log in here
The PowerG Wireless Smoke and Heat Detector provides early warning of fire. It alerts occupants of the room by activating the built-in 85db alarm buzzer and flashing LED light when smoke or temperature exceeding 57°C (135°F) are detected. At the same time, it transmits a coded signal to the control panel to activate the system siren, alerting the end user and/or central monitoring station to send onsite assistance.
- Provides accurate early fire warning, with audio and visual alerts, when smoke or high temperature is detected
- Enhances safety and facilitates maintenance, with alerts for device tampering and low battery
- Robust industry leading PowerG commercial grade wireless technology
- Offers long-lasting value with a 3-year battery life (with typical use)
- Large transmission range enables repeater-free installations
- Speeds up installations with visible link quality indicator on the device
- Simple wall or ceiling installation, with bracket
- Protected by a back tamper
Item#:
PG9936
You must be logged in to order this item.
Log in here
S2K Administration - Form Template Display
Actions
(Denotes required field.)