S2K Commerce - Products Dropdown
Actions
S2K Commerce - Shopping Cart
Actions
S2K Commerce - Order Entry
Actions
The ENFORCER HDMI Extender over Single Cat5e/6 extends the range of traditional HDMI cabling methods by using an active transmitter and receiver to send video and audio over a single Cat5e/6 cable. HDMI formats as large as 1080p can be transmitted up to 164ft (50m) between the two units with zero signal loss by using integrated circuits in the receiver and transmitter. The extender also supports HDMI loop output, EDID management settings, and one way IR control for remotely controlling HDMI sources and displays.
- Extend HDMI over a single Cat5e/6 cable
- Supports resolutions from 480i to 1080p with zero signal loss
- Transmits up to 164ft (50m) at 1080p over Cat5e/6 cable
- HDMI Loop output for local HDMI display
- Plug and play operation – comes as a complete set
- IR Pass-through for remote control extension and operation
- EDID Management switch
- Two (2) 5VDC power supplies included
Item#:
MVE-AH1E1-01NQ
You must be logged in to order this item.
Log in here
Altronix T1RV3F4 rack kit is pre-assembled and consists of Trove1M1R enclosure/backplane with factory installed Altronix power supply/charger and sub-assemblies. This kit also accommodates various combinations of HID VertX® boards for up to six (6) doors in a single enclosure.
Power Supply (eFlow6NB):
Input
- Voltage: 120VAC, 60Hz, 3.5A max.
- Fusing: 5A / 250V.
Output
- Voltage: Factory set at 24VDC.
- Current: 6A continuous.
- Maximum Supply Current for Main and Aux. Outputs on eFlow6NB Power Supply board, PDS8 Power Distribution Module’s and ACM4 Access Power Controller’s outputs is 5.6A.
- Auxiliary: Class 2 power-limited @ 1A (unswitched).
- Other: Overvoltage protection. Filtered and regulated.
Battery Backup
- Built-in charger for sealed lead acid or gel type batteries (if batteries are required, install separate battery enclosure RE2).
- Automatic switch over to stand-by battery when AC fails.
- Zero voltage drop when unit switches over to battery backup (AC failure condition).
Fire Alarm Disconnect
- Supervised: Latching or non latching.
- EOL: 10K Resistor.
Supervision
- AC Failure: Form “C” contacts.
- Battery: Form “C” contacts.
- Low DC Power Shutdown: Shuts down DC output terminals if battery voltage drops below 70-75% for 24V units. Prevents deep battery discharge.
Indicators LED
- Input: 120VAC is present.
- DC Output: Powered.
- Battery: Discharged or not connected.
Access Power Controller (ACM4):
Input
- Voltage: 24VDC from eFlow6NB.
- Fusing: 10A / 250V.
Output
- Voltage: 24VDC.
- Four (4) independently controlled 2.5A outputs:
- a) Four (4) Fail-Safe and/or Fail-Secure power outputs.
- b) Four (4) dry form “C” 5A rated relay outputs.
- c) Any combination of the above.
- Four (4) auxiliary power outputs (unswitched).
- Fuses Rating: 3A / 32VDC.
Indicators (LED)
- Red LEDs: Outputs are triggered (relays energized).
- Blue LED: FACP disconnect is triggered.
Power Distribution Module (PDS8):
Input
- Voltage: 24VDC from eFlow6NB and 12VDC from VR6.
- Fusing: 10A / 250V.
Output
- Voltage: 12 or 24VDC individually selectable.
- Fuses Rating: 3A / 32VDC.
Indicators (LED)
- DC Output: Eight (8) individual output LEDs.
Item#:
T1RV3F4
You must be logged in to order this item.
Log in here
Includes: both enclosures, NXT-3R reader, PSC-35 power supply, (3) NXT-C,(2) NXT-AP, works with VisualDoors only
- Economical mini-controller for a single door
- Works exclusively with Keri’s Visual DoorsTM software
- Networkable via RS-485 for up to 8 controllers
- Supports Keri NXT and NXT-E readers
- Capable of In/Out access using Keri’s a NXT-E reader in conjunction with a standard NXT reader
- 1000 credential capacity
- 4000 Event buffer (offline)
- Equipped with dedicated inputs for REX & Door Sense
- Form "C" Relay for door control
- Configurable for: Lock Time, Auto Unlock by time
- 8 Access Groups configurable per credential
- Same small footprint as Keri’s Intelliprox BlueTM and sharing the same enclosure
Item#:
NEUT-3R-KIT
You must be logged in to order this item.
Log in here
S2K Administration - Form Template Display
Actions
(Denotes required field.)