The GEM-K4RF is a multi-segment LCD digital keypad that is compatible with the NAPCO GEM-Series GEM-P816, P1632, P3200 & P9600 control panels.

Features:

• Large backlit, fixed English display
• Built-in 32 Point Gemini wireless receiver for labor-saving convenience
• Proven crystal-control wireless performance
• Supports all Gemini transmitters
• New stay & away ease-of-use buttons, for easy one button arm
• EZ-Programming mode
• New intuitive, stay & away ease-of-use buttons, for easy one button arm and easy "instant" (hold-down)
• Large soft touch backlit keys with tone
• Backlit displays for easy reading
• Wireless transmitter signal strength indication
• Decor friendly soft white design
• Fire, police and auxiliary programmable panic keys
• Fingertip reference chart

• Battery powered design runs on 4 “AA” batteries
• Extremely long 2 year battery life
• Can be powered by 24 VAC “C” wire from HVAC system
• Z-Wave compatible – Ver. 4.5.5
• Supports Z-Wave FLiRS functionality
• Works on standard HVAC systems: 2 stage heat/ 2 stage cool
• Works on heat pump HVAC systems: 3 stage heat/ 2 stage cool
• Incredibly easy to install and program
• USB firmware upgrade ability
• Wall mount or mounts on single-gang junction box

The GEM-RECV-XP8 will accommodate up to 8 wireless transmitters, 4 GEM-SMK wireless smoke detectors, and 4 GEM-KEYF key fob transmitters. The receiver is connected to the keypad 3-wire bus. The receiver monitors each transmitter, updating transmitter status as reports are received, and coveys this information to the control panel. Also monitored is the elapsed time since the last report from each transmitter. If no report is received within a programmed time, the panel will issue a Supervisory Failure system trouble.

PIR Motion Detection

• ETL certified for UL 639
• Wireless connectivity for easy installation
• Configurable PIR sensitivity including pet immunity

The Wireless Touch Screen Keypad (2GIG-TS1) is a wall-mounted, full-color, touch screen interface that provides many of the same easy-to-use keypad functions available on the control panel. It is designed for indoor use only and gives users the ability to control lights, thermostats, and door locks, as well as to view the status of every sensor zone.

When the 900 MHz Transceiver Module (2GIG-XCVR2-345) is installed in the GC2 control panel, the system can be programmed to communicate with up to four (4) Wireless Touch Screen Keypads.

Features:

• Full color touch screen interface
• Same easy-to-use interface as the GC2 panel
• One-touch Home and Emergency navigation
• Add up to 4 Wireless Touch Screen Keypads to 1 system
• Easy access to Z-Wave functionality
• See and hear system status, chimes and alerts
• Screen and buttons can be configured to darken completely and light back up with one touch
• Requires XCVR2 to be installed in main panel

• 1,100 Users over 2 Outputs. Codes may be 4~8 digits: - Output #1  Form C relay, 1A@30VDC, 1,000 users - Output #2  Form C relay, 1A@30VDC, 100 users
• Outputs can be programmed to activate for up to 99,999 seconds (nearly 28 hours)
• Super user code gives admin access to keypad
• Up to 50 (01~50) possible temporary visitor codes, which can be programmed for one-time or limited-time use (1~99 hours)
• Programmable egress input with optional warning alarm and delayed egress
• Real-time clock to auto-disable access at specific times
• Up to 50 (01~50) duress codes for output #1 and 10 (01~10) for output #2
• Duress code signals a silent alarm if an authorized user is forced to open the door under duress
• 12~24 VDC/VAC Auto-adjusting operation
• All features are programmed directly from the keypad: No need for an external programmer
• IP66 Weatherproof Rating
• Mounts to a standard single-gang back box (surface-mount back box included)
• Durable and attractive stainless steel faceplate
• Tamper output: N.C. Dry contact, 50mA@24VDC max.
• Keypad illuminates when a button is pressed; backlight can be programmed for FULL, AUTO, or OFF in standby mode
• Mantrap: for a protected area with two doors, this feature allows only one door to be open at a time
• Door sensor input for anti-tailgating operation
• Door-propped-open warning
• Door-forced-open warning
• EEPROM Memory protects programmed information in case of power loss

The 2GIG 319/345 MHz Receiver is designed to be installed into the 2GIG GC2 Panel. This Receiver is a dual frequency device, enabling communication between the Control Panel and peripheral devices that use either the 319 or the 345 MHz frequency.

Features:

• InterLogix-compatible 319MHz wireless protocol
• Integrated into panel, no external power supply or translator hardware
• Easy to install into any GC2 panel
• Accepts up to 48 wireless devices using 2GIG, Honeywell, or InterLogix protocols
• External antenna provides reliable range performance

• Up to 1,000 possible user codes (4-8 digits)
• Output: Form C relay, 1A@30VDC max.
• Output can be programmed to activate for up to 99,999 seconds (nearly 28 hours)
• Up to 50 (01~50) possible temporary visitor codes, which can be programmed for onetime or limited-time use (1~99 hours)
• Durable and attractive stainless-steel faceplate
• Programmable delayed egress input lets users exit the premises without keying in the code
• EEPROM Memory protects programmed information in case of power loss
• 12~24 VDC/VAC Auto-adjusting operation
• Tamper output: N.C. Dry contact, 50mA@24VDC max.
• Mounts to a standard single-gang back box (surface-mount back box included)
• Programmable wrong-code lockout
• Real-time clock to auto-disable access at specific times
• All features are programmed directly from the keypad: No need for an external programmer