S2K Commerce - Products Dropdown
Actions
S2K Commerce - Shopping Cart
Actions
S2K Commerce - Order Entry
Actions
The Model DXR-701 is a digital receiver with an isolated relay output designed for use with Linears DX Format transmitters. This receiver can be used in a variety of remote control applications. When the receiver detects a signal from a transmitter programmed into its memory, the relay output activates. The relay has four optional output configurations.
In a typical installation, the receiver is connected to an alarm control panel, door strike, camera, high current relay or some other device. A transmitter is used to activate or control the device. The receiver should be mounted with the supplied mounting bracket indoors or outdoors inside a weather resistant non-metallic housing.
The digital DX code format features over a million possible codes. The DX transmitters are precoded at the factory to unique codes, so no field coding is required. Receivers must be programmed to the transmitters code before system testing and operation. Up to 32 transmitters can be programmed into the receivers memory. The memory is retained, even without power.
The unit can be powered from a 11-17 VDC or 12-16 VAC power source. The relays normally open and normally closed contacts can switch up to 1 amp at 24 volts AC/DC.
Cutting jumpers select how the relay activates. The factory setting causes the relay to engage for four seconds each activation. Optionally, the relay can be set to engage for one second, toggle on with one activation then off with the next, or latch engaged until reset by pressing the program button.
A nine-inch wire lead serves as the receivers antenna. The red program indicator lights during RF reception. The installer can verify that signals are being sent from transmitters and diagnose interference problems by viewing the indicator. The indicator also lights during memory programming/erasing and flashes to count the number of transmitters in memory.
Features:
- 32 transmitter capacity
- RF activity indicator
- Quick-learn programming
- Operates on 11-17 VDC or 12-16 VAC power
- One channel
- DX format
- One form C relay output
- One Amp contact rating @ 24 Volts AC/DC
- Selectable relay activation time
- Current consumption: 25 mA standby, 60 mA operating @ 12 VDC
- RF frequency: 315 MHz
- 5.5 in. W x 4.0 in. H x 1.25 in. D
- Order number: SNR00148
- FlexCoreTM Signal Processor - The FlexCore Signal Processor is an Application-Specific Integrated Circuit (ASIC), which processes sound data in parallel rather than sequentially for faster, more accurate detection decisions. The combination of proven FlexGuard ® performance with the speed of FlexCore processing provides unmatched false alarm immunity without compromising detection.
- V-Plex Polling Loop Technology - V-Plex devices are installed using two wires for power and data. In addition, V-Plex technology features Point Identification, allowing users to quickly pinpoint the source of an alarm or trouble condition.
- Easy Installation and Setup - Honeywell’s patented technology allows remote activation of Test Mode (with simulator). The FG1625SN has a centered wire entry hole, 45° terminal blocks, and EOL terminals. A hand-clap feature verifies that the detector is functioning.
- Selectable Sensitivity - Two dip switches on the FG1625SN make it easy to set the sensitivity to match the acoustics of the room. Four different sensitivity levels are available, ranging from very low to high. The range can then be verified remotely with the FlexGuard FG-701 Glassbreak Simulator.
- Mount the Detector Anywhere - Mounts on any wall, in the window frame, or on the ceiling, with no minimum range and a maximum range of 25’ (7.6 m) to the glass.
- Covers All Glass Types - The FG1625SN works on all glass types, including plate, tempered, laminated, wired, film-coated, and sealed insulating glass.
- Multiple Domain Signal Analysis - The FG1625SN performs Multiple Domain Signal Analysis in which time, frequency and amplitude characteristics are evaluated for signal qualification. This enables the detector to accurately discriminate false alarms from true glassbreak events.
- Enclosed PC Board - The PCB is protected from potential damage during installation.
- Patented Remote Test Mode - The Patented Remote Test Mode can enable or disable the indicator LEDs using the FG-701 Glassbreak Simulator. The unit automatically resets from Test Mode in five minutes.
- Mounting Locations - The FG1625SN can be mounted on the ceiling, opposite wall, adjoining wall, or the same wall as the glass.
S2K Administration - Form Template Display
Actions