|◀ 145 - 156 of 22392 ▶|
View:
Item#:
MC1000
You must be logged in to order this item. Log in here
The Model ACT-31B 1-Channel Block Coded Key Ring Transmitter is designed for use with Linear’s access control products. The Model ACT-31B is a single-channel device supplied with a quick-disconnect key ring. Also included are lithium batteries with a five-year service life. A unique 10-second time-out feature prevents the system from being shut down by a single transmitter transmitting continuously.

The transmitter is MegaCode format, which means each transmitter is factory preprogrammed with one of over 1,000,000 codes, virtually eliminating the possibility of code duplication. Because the receiver ”learns” each specific code, no unauthorized person can gain access to the system by reprogramming a transmitter.

Block coded transmitters are factory programmed to a sequential series of transmitter ID codes. When used with a Linear access controller, transmitters can be locally or remotely programmed into memory by entering the first and last codes of the block into the system. Facility codes can be selected to further customize the system.
 
  • Compatible with all Linear access receivers and controllers
  • Supplied with quick-disconnect key ring
  • Sold in lots of 10
  • Power: Two 2016 batteries
  • Codes: Factory block coded in MegaCode format
  • RF frequency: 318 MHz
Item#:
ACT-31B
You must be logged in to order this item. Log in here
You must be logged in to order this item. Log in here
You must be logged in to order this item. Log in here
You must be logged in to order this item. Log in here

Altronix ACM8CB converts one (1) 12 to 24 volt AC or DC input into eight (8) independently controlled Class 2 rated PTC protected power-limited auto-resettable outputs rated at 2.5A each. Outputs are activated by an open collector sink or normally open (NO) dry trigger input from an Access Control System, Card Reader, Keypad, Push Button, PIR, etc. ACM8CB will route power to a variety of access control hardware devices including Mag Locks, Electric Strikes, Magnetic Door Holders, etc. Outputs will operate in both Fail-Safe and/or Fail-Secure modes. This unit is designed to be powered by one common power source which will provide power for both the board operation and locking devices, or two (2) totally independent power sources, one (1) providing power for board operation and the other for lock / accessory power. The FACP Interface enables Emergency Egress, Alarm Monitoring, or may be used to trigger other auxiliary devices. The fire alarm disconnect feature is individually selectable for any or all of the eight (8) outputs.

Features

  • Fire Alarm disconnect (latching or non-latching) is individually selectable for any or all of the eight (8) outputs.
    Fire Alarm disconnect input options:
    • a) Normally open (NO) or normally closed (NC) dry contact input.
    • b) Polarity reversal input from FACP signaling circuit.
  • FACP output relay (form "C" contact rated @ 1A 28VDC not evaluated by UL).
  • Removable terminal blocks facilitate ease of installation.

Item#:
ACM8CB
You must be logged in to order this item. Log in here
You must be logged in to order this item. Log in here
You must be logged in to order this item. Log in here

The EM-Mag1500 compact electromechanical lock is designed for outswinging doors and small enclosures. The RCI EM-Mag1500 is significantly smaller than standard electromagnetic locks. This electromechanical solution includes a bi-color light panel for indicating lock status, an early warning alarm, and an anti-tamper security plate.

  • Energy: 240mA Field-Selectable 12/24VDC (At 12VDC, 120mA at 24VDC)
  • Strength: 1,500lbf Holding Force
  • Mode: Fail-Safe
  • Monitor: Lock & Door Status Sensors
  • Warranty: 3 Year Limited Warranty

Item#:
EM-MAG1500
You must be logged in to order this item. Log in here
You must be logged in to order this item. Log in here

  • RF Modulation: ASK at 125 kHz
  • Internal sounder with external control option
  • Tri-color LED with external control inputs
  • External reader hold control
  • Optical wall tamper detection
  • Water-resistant with epoxy potting (IP65), suitable for indoor and outdoor applications
  • Made of tough polycarbonate UV-resistant plastic
  • Comes with mounting template for easier installation
Item#:
AY-H12C
You must be logged in to order this item. Log in here
You must be logged in to order this item. Log in here
|◀ 145 - 156 of 22392 ▶|
View:
(Denotes required field.)