|◀ ◀ 121 - 132 of 23621 ▶ ▶|
View:

Gate Lock, 12/24VDC, Standard Fail Safe

The heavy duty GL1 Electromechanical Gate Lock provides weather-resistant access control for a wide range of gate applications. The GL1 provides 2000lbs of holding force for electrical and manually operated indoor or outdoor gates where preload is a concern. Ideal for swinging or sliding Product features vehicle, pedestrian, or stock gate access control.

Features

  • 2,000 lbs holding force
  • Operates under preload up to 100lbs
  • Automatic dual voltage - no field adjustment required
  • Accepts a standard mortise cylinder with Adams Rite MS cam for manual key override (not included, see spacer guide below)
  • Self-aligning receiver (+/- 1/2 in. horizontally) helps compensate for gate misalignment and sag
  • Tamper resistant cast housing
  • Optional latch status monitor
  • Surface mount
  • MagnaCare lifetime replacement, no fault warranty

Item#:
GL1-FS
You must be logged in to order this item. Log in here

Power Supply Charger, Single Class 2 Output, 12/24VDC @ 6A, 115VAC

AL600ULX is a power supply/charger which converts a 115VAC/60Hz input into a single 12VDC or 24VDC non power-limited output.

Input

  • Input 115VAC, 60Hz, 3.5A.
Output
  • 12VDC or 24VDC selectable output.
  • 6A continuous supply current.
  • Filtered and electronically regulated output.
  • Short circuit and thermal overload protection.

Item#:
AL600ULX
You must be logged in to order this item. Log in here

KT-2 two door IP controller wi th KT-2-CAB-M cabinet.

Item#:
KT-2-M
You must be logged in to order this item. Log in here

PIR REX Sensor WH 2 Form C DPD T 12/24vDC Contacts & W/Term

Item#:
CM-RQE70A
You must be logged in to order this item. Log in here

35ft Reflective Photoelectric Beam Sensor

  • For outdoors gates, garage doors, etc.
  • Adjustable sensing range
  • 12~240 VDC / 24~240 VAC Operation
  • Current draw: Up to 40mA@12VDC
  • For indoor or outdoor use (IP66)
  • Pre-wired 6.5ft (2m) cord
  • Brackets and mounting hardware included
  • Compact size
  • New single-gang box and wall-mount brackets available
Item#:
E-931-S35RRQ
You must be logged in to order this item. Log in here

KRYPTO A22K CONTROLLER- NO BOX

Item#:
A22K-NB
You must be logged in to order this item. Log in here

Protege Prewired Expn Kit - 4 Doors

Item#:
KIT-EXP-4D
You must be logged in to order this item. Log in here

3/4" Magnetic Bridle Ring, UL Listed 40 lbs Silver pack of 1

Item#:
BRM75-100 MAG
You must be logged in to order this item. Log in here

Glass Mount Kit for 600lbs Mag netic Lock

Item#:
CX-MA0611
You must be logged in to order this item. Log in here

Access Power Controller, 8 PTC Class 2 Relay Outputs, FAI, Board

Altronix ACM8CB converts one (1) 12 to 24 volt AC or DC input into eight (8) independently controlled Class 2 rated PTC protected power-limited auto-resettable outputs rated at 2.5A each. Outputs are activated by an open collector sink or normally open (NO) dry trigger input from an Access Control System, Card Reader, Keypad, Push Button, PIR, etc. ACM8CB will route power to a variety of access control hardware devices including Mag Locks, Electric Strikes, Magnetic Door Holders, etc. Outputs will operate in both Fail-Safe and/or Fail-Secure modes. This unit is designed to be powered by one common power source which will provide power for both the board operation and locking devices, or two (2) totally independent power sources, one (1) providing power for board operation and the other for lock / accessory power. The FACP Interface enables Emergency Egress, Alarm Monitoring, or may be used to trigger other auxiliary devices. The fire alarm disconnect feature is individually selectable for any or all of the eight (8) outputs.

Features

  • Fire Alarm disconnect (latching or non-latching) is individually selectable for any or all of the eight (8) outputs.
    Fire Alarm disconnect input options:
    • a) Normally open (NO) or normally closed (NC) dry contact input.
    • b) Polarity reversal input from FACP signaling circuit.
  • FACP output relay (form "C" contact rated @ 1A 28VDC not evaluated by UL).
  • Removable terminal blocks facilitate ease of installation.

Item#:
ACM8CB
You must be logged in to order this item. Log in here

2-Door Expander

The MD-D02B is a plug-in expansion module for Rosslare’s AC-225x-B access control panels that provides a 2-reader interface, 4 supervised inputs with end-of-line (EOL) resistor protection, and 4 relay outputs (5 Amp Form-C N.O./N.C.) to the panel. Installation of the module takes under one minute with the tailored expansion port in the panels and auto-recognize by the panel. Once it is installed and the panel is powered on, the expansion is recognized by the AxTraxNG server, and the MD-D02B can be programmed for access control and automation. Advanced communication with the controller allows for firmware update and real-time event logging, with support for full offline operation by the host panel.
  • Additional two proximity readers or keypads
  • Four relay outputs and four supervised inputs to the access control panel
  • Wiegand or Clock-and-Data transmission keypad or biometric reader compatibility
  • LED status feedback for 12 V power and relay activation
  • Cost effective and modular installation
  • Input and output configurability using Rosslare’s AxTraxNG™ software
Item#:
MD-D02B
You must be logged in to order this item. Log in here

1/2 Inch Spacer for 1200 lb. Lock

Item#:
AM6300
You must be logged in to order this item. Log in here
|◀ ◀ 121 - 132 of 23621 ▶ ▶|
View:
(Denotes required field.)