|◀ 109 - 120 of 22396 ▶|
View:

  • Emergency Exit Buttons offer additional safety, as required by code, for possible malfunction of motion exit sensor
  • Mounted next to door
  • Momentarily pressing the button releases door for 30 seconds
  • Retriggerable
  • Single Gang or Narrow Stile
  • SPST 3 Amp wet N/C contacts
  • Operates on 12 or 24 VDC (must be same voltage as the installed lock)
  • For indoor use only
  • EEB3N includes switchable green and red lenses
  • UL Listed

Item#:
EEB3N
You must be logged in to order this item. Log in here

The heavy duty GL1 Electromechanical Gate Lock provides weather-resistant access control for a wide range of gate applications. The GL1 provides 2000lbs of holding force for electrical and manually operated indoor or outdoor gates where preload is a concern. Ideal for swinging or sliding Product features vehicle, pedestrian, or stock gate access control.

Features

  • 2,000 lbs holding force
  • Operates under preload up to 100lbs
  • Automatic dual voltage - no field adjustment required
  • Accepts a standard mortise cylinder with Adams Rite MS cam for manual key override (not included, see spacer guide below)
  • Self-aligning receiver (+/- 1/2 in. horizontally) helps compensate for gate misalignment and sag
  • Tamper resistant cast housing
  • Optional latch status monitor
  • Surface mount
  • MagnaCare lifetime replacement, no fault warranty

Item#:
GL1-FSM
You must be logged in to order this item. Log in here
You must be logged in to order this item. Log in here
You must be logged in to order this item. Log in here

Altronix AL1024ULACM converts a 115VAC 60Hz input into eight (8) independently controlled 24VDC Fail-Safe and/or Fail-Secure outputs with a total of 10A continuous supply current. Outputs are activated by an open collector sink or normally open (NO) dry trigger input from an Access Control System, Card Reader, Keypad, Push Button, PIR, etc. This unit will route power to a variety of access control hardware devices including Mag Locks, Electric Strikes, Magnetic Door Holders, etc. The outputs will operate in both Fail-Safe and/or Fail-Secure modes. This unit is designed to be powered by one common power source (factory installed) which will provide power for both the board operation and locking devices, or two (2) totally independent power sources, one (1) providing power for board operation and the other for lock / accessory power. The FACP Interface enables Emergency Egress, Alarm Monitoring, or may be used to trigger other auxiliary devices. The fire alarm disconnect feature is individually selectable for any or all of the eight (8) outputs.

Features

  • Fire Alarm disconnect (latching or non-latching) is individually selectable for any or all of the eight (8) outputs.
    Fire Alarm disconnect input options:
    • a) Normally open (NO) or normally closed (NC) dry contact input.
    • b) Polarity reversal input from FACP signaling circuit.
  • Alarm output relay indicates that FACP input is triggered (form "C" contact rated @ 1A 28VDC not evaluated by UL).
  • Short circuit and thermal overload protection.

Item#:
AL1024ULACM
You must be logged in to order this item. Log in here
  • Users/Fingerprints: 5000
  • Event Buffer:10,000 Reader
  • Ports:2 (Support multi format Weigand or OSDP Readers)
  • Communication: TCP/IP/Wifi and RS485 for FP and OSDP Readers
  • Input Ports: 5 (2 exit buttons, 2 door sensors and 1 Aux Input)
  • Output Ports: 3 (2 FORM-C Relay Output for lock, 1 Aux Output Relay)
  • Gross Weight: 3 lbs.
  • Package Size: 12" x 9" x 4"
Item#:
ATLAS260
You must be logged in to order this item. Log in here
Item#:
LANDO-CS-14X10-E
You must be logged in to order this item. Log in here
You must be logged in to order this item. Log in here
You must be logged in to order this item. Log in here
You must be logged in to order this item. Log in here
You must be logged in to order this item. Log in here
You must be logged in to order this item. Log in here
|◀ 109 - 120 of 22396 ▶|
View:
(Denotes required field.)