CONTROLS/ACCESSORIES - Page 3 of 233

Compare

Communication Interlink Module

The CIM is a communication control module designed to use a CAN Bus communication network. Keyscans CIM provides optimized server to access control unit (ACU) communication. The Communication Interlink Module creates a new inter-panel ACU to ACU communication network that provides global communication functions including anti-passback, global input/output and global time zones. The CIM includes an impressive host of new features including ground loop protection, enhanced diagnostics, improved speed and unprecedented reliability.

Features

Provides optimized server to Access Control Unit (ACU) communication

Gives users a new ACU to ACU network providing inter-panel communication for global functions

Standardized Cabling establishes communication links with CAN Bus communication protocol using standard CAT5 cabling

Ground Loop Tolerance maximizes electrical isolation to earth ground providing tolerance against ground loops

Fault Tolerance ensures if one CIM fails it wont take the loop down with it. The CAN Bus protocol offers non-interrupted communication of remaining devices on the network

Communication Speeds provides optimized communication speeds, up to 115K BPS

Enhanced Diagnostics for quick and easy troubleshooting

Auto Bit Rate Conguration to automatically match bit rate speed with control unit conguration

Supports Keyscans plug-on TCP/IP network adapter NETCOM2P/6P

Uses a simplied ribbon cable connection to control unit for fast installation

Access Control Units with direct connectivity with the CAN Bus network now provide ACU to ACU to communication without server dependence. This permits a host of new features and capabilities

Item#:

CIM

You must be logged in to order this item. Log in here

Compare

4-Door Expander

Rosslare’s MD-D04B is a plug-in expansion module for Rosslare’s AC-425x-B access control panels that provides a 4-reader interface, 4 supervised inputs with end-of line (EOL) resistor protection, and 4 relay outputs (5 Amp Form-C N.O./N.C.) to the panel. Installation of the module takes under one minute with the tailored expansion port in the panels and auto-recognize by the panel. Once it is installed and the panel is powered on, the expansion is recognized by the AxTraxNG Server, and the MD-D04B can be programmed for access control and automation. Advanced communication with the controller allows for firmware update and real-time event logging, with support for full offline operation by the host panel.

Additional four proximity readers or keypads
Four relay outputs and four supervised inputs to the access control panel
Wiegand or Clock-and-Data transmission keypad or biometric reader compatibility
LED status feedback for 12 V power and relay activation
Cost effective and modular installation
Compatible with Rosslare’s AC-425 networked controller
Input and output configurability using Rosslare’s AxTraxNG software

Item#:

MD-D04B

You must be logged in to order this item. Log in here

Compare

RS232 to TCP/IP Converter

The NETCOM2 is an off-board TCP/IP communication module designed to establish access control units as a network-appliance based unit. The Keyscan NETCOM2 functions with new and legacy access control units and allows a quick connection to an existing LAN/WAN network infrastructure. NETCOM2 features DIP switches for convenient set up and is programmable for easy conguration when establishing communication along a network infrastructure.

Features

Features embedded IP addresses for programming the device on a local network

Provides serial connection from the ACUs via 10/100 RJ45 network interface to communicate with a server or PC host

Use static TCP/IP addresses to allow communication over an existing LAN/WAN network

Unlimited units can be added to a system, oering an enterprise solution

Fast, easy, trouble-free o-board installation

Allows one or more Access Control Unit(s) to communicate on a LAN/WAN

DIP switch settings for convenient conguration

Fast and easy installation for each ACU

Static TCP/IP communication protocol between PC NIC (Network Interface Card) and Access Control Unit(s) featuring NETCOM2

Requires Static IP addresses for proper operation

Simplies both installation and maintenance procedures

Item#:

NETCOM2

You must be logged in to order this item. Log in here

Compare

Single Door PoE Equipped Control Unit

When it comes to performance, and overall capability, the CA150 is comparable with our full line of access control units. CA150 is ideal for a single-door deployment or to augment an existing system with a need for one additional door.

Network connectivity with built-in PoE ready TCP/IP module

PoE mode powers reader, strike, and other auxiliary devices, up to 680mA.

DHCP supported

Dual Processors

Flash Memory

Two reader ports

Item#:

CA150

You must be logged in to order this item. Log in here

Compare

ProWireless Mesh Network Repeater

Repeaters can be used to increase the distance of the wireless signal in areas where signal strength is weak, or the signal needs to travel long distances between door controllers. Repeaters become part of the mesh network and connect with each other or directly to an ACP, door controllers, and cloud node.

Communication:

WiMACTM Wireless Mesh (2.4 GHz / 802.15.4)
Encryption: AES 128bit
Wireless Range: 1 Mile LoS, 450ft indoor average

Power:

Includes wall plug with 6ft cable
3.3V-5V up to 500mA

Item#:

MNR

You must be logged in to order this item. Log in here