S2K Commerce - Products Dropdown
Actions
S2K Commerce - Shopping Cart
Actions
S2K Commerce - Order Entry
Actions
This item has been discontinued and replaced by item
2GIG-GB100-345
The Glass Break Detector is a fully-supervised, tamper-protected, ceiling- or wall-mounted unit. It communicates with the 2GIG Control Panel using the 345 MHz frequency. The detector provides a 15 ft (4.6 m) maximum detection range, 360° maximum horizontal sensing angle, and dual-stage glass break detection.
Features:
Item#:
2GIG-GB1-345
You must be logged in to order this item.
Log in here
- For sensing things that open or separate.
- Magnet and Internal reed switch operation
- 2 supplemental hardwire zones
- GE-compatible version reports 2nd zone to 2nd ID
- Cover tamper
- Strong, reliable RF signal
- 10-15 year battery life on CR123A battery
- Low Battery indication
Item#:
RE101
You must be logged in to order this item.
Log in here
Alula's Connect+ Sensor Repeater provides batterybacked extension of Connect+ sensors. Extending coverage ensures proper sensor signal strength, preventing costly service calls.
- Extends Range of Connect+ Wireless Sensors
- Rechargeable backup battery
- Cover and Wall Tamper
- 5-year Warranty
Item#:
RE620
You must be logged in to order this item.
Log in here
Indoor Motion Sensor, Pet Immune, Honeywell Compatible.
Item#:
RE211P
You must be logged in to order this item.
Log in here
- Transmits power at the full FCC limits, maximizing range
- Support for an external contact
- 1-inch magnet gap
- cover tamper
- 6+ year battery life
Item#:
RE322
You must be logged in to order this item.
Log in here
PINPad is a small keypad featuring 1-button arming with a secure, 4-digit disarm code. PINPad can be wall-mounted, attached to a car visor, or carried in a purse or backpack.
- Secure, 4-10-digit code to disarm
- 1-button arming
- Mounts on wall via VHB tape
- Option to use as primary or backup-keypad device
- LED indicator
- Reversible backplate for wall or table top mounting
Item#:
RE652
You must be logged in to order this item.
Log in here
The Qolsys QS7134-840 IQ Hardwire 16-F w/ Large Enclosure is a wired to wireless system converter that transmits signals at the 319.5 MHz frequency. By using this module, you can bring over your existing hardwired sensors and use them with your 319.5 MHz wireless security system.
The way that the Qolsys IQ Hardwire 16-F works is very simple. It has 16 on-board zone terminal pairs for connecting hardwired sensors. Each zone features its own LED light to assist with enrollment and troubleshooting. A resistor must be used at each zone. In Legacy Mode, the QS7134-840 can be calibrated to use 1k to 10k resistors that are wired in parallel (NO) or series (NC). This differs from the older-style QS7133-840 that was restricted to only supporting 4.7k resistors (Yellow-Violet-Black-Brown-Brown). However, all versions of the Qolsys IQ Hardwire 16-F come with the same 4.7k resistors that must be used to meet UL Standards for fire protection. These resistors work great, so it is advised that you just use the included ones to avoid any possible confusion.
For primary power, the Qolsys IQ Hardwire 16-F uses its included 16VDC transformer. This transformer features an attached power cable for connecting with the module. On the cable, the wire with the grey dashes is the positive (+) connector. The unmarked wire represents the negative (-) connector. If you damage the transformer or the attached cable, then you will need to get a replacement 16VDC transformer.
The way that the Qolsys IQ Hardwire 16-F works is very simple. It has 16 on-board zone terminal pairs for connecting hardwired sensors. Each zone features its own LED light to assist with enrollment and troubleshooting. A resistor must be used at each zone. In Legacy Mode, the QS7134-840 can be calibrated to use 1k to 10k resistors that are wired in parallel (NO) or series (NC). This differs from the older-style QS7133-840 that was restricted to only supporting 4.7k resistors (Yellow-Violet-Black-Brown-Brown). However, all versions of the Qolsys IQ Hardwire 16-F come with the same 4.7k resistors that must be used to meet UL Standards for fire protection. These resistors work great, so it is advised that you just use the included ones to avoid any possible confusion.
For primary power, the Qolsys IQ Hardwire 16-F uses its included 16VDC transformer. This transformer features an attached power cable for connecting with the module. On the cable, the wire with the grey dashes is the positive (+) connector. The unmarked wire represents the negative (-) connector. If you damage the transformer or the attached cable, then you will need to get a replacement 16VDC transformer.
Item#:
QS7134-840
You must be logged in to order this item.
Log in here
S2K Administration - Form Template Display
Actions
(Denotes required field.)