S2K Commerce - Products Dropdown
Actions
S2K Commerce - Shopping Cart
Actions
S2K Commerce - Order Entry
Actions
- Compatible with any hardwired sensors going to the various wireless panels
- 8 Hardwire loops with end-of-line resistor detection
- Unique wireless ID (or loop) for each zone
- Unique wireless ID for the device itself
- Transmit diversity for long reliable range
- PIR powering (via external supply)
- Device low battery detect
- Device tamper detect
- External 12VDC power supply required (sold separately
The way that the Qolsys IQ Hardwire 16-F works is very simple. It has 16 on-board zone terminal pairs for connecting hardwired sensors. Each zone features its own LED light to assist with enrollment and troubleshooting. A resistor must be used at each zone. In Legacy Mode, the QS7134-840 can be calibrated to use 1k to 10k resistors that are wired in parallel (NO) or series (NC). This differs from the older-style QS7133-840 that was restricted to only supporting 4.7k resistors (Yellow-Violet-Black-Brown-Brown). However, all versions of the Qolsys IQ Hardwire 16-F come with the same 4.7k resistors that must be used to meet UL Standards for fire protection. These resistors work great, so it is advised that you just use the included ones to avoid any possible confusion.
For primary power, the Qolsys IQ Hardwire 16-F uses its included 16VDC transformer. This transformer features an attached power cable for connecting with the module. On the cable, the wire with the grey dashes is the positive (+) connector. The unmarked wire represents the negative (-) connector. If you damage the transformer or the attached cable, then you will need to get a replacement 16VDC transformer.
The IQ Glass is specially designed to protect you if an intruder tries to break-in through a window. Using our proprietary S-Line encryption technology, encrypts signals sent to the IQ Panel while still providing backwards compatibility for legacy 319.5 systems. Triggered by the pitch and frequency of breaking glass, the IQ Glass is effective within 25 ft. and is activated automatically when you arm your IQ Panel in either "Stay" or "Away" mode. Typically installed on the opposite wall or on the ceiling to allow for better "listening" ability in large living areas.
- Encrypted S-Line sensor technology protects signals sent to the IQ Panel while still providing support for legacy 319.5 systems
- Actively listening for breaking glass frequencies when you are in "stay" or "away" modes
- Typically installed on the wall opposite the windows needing protection, or on the ceiling in a room with windows on multiple sides
- Protects widows within line of sight within 25 ft.
NanoMax is the smallest full-featured security transmitter in the industry. It is typically used to sense opening and closings of doors and windows, but can secure just about anything using its Strip & Stick external contact holes. It will alarm when the magnet is pulled away from the NanoMax or when the external contact is opened.
- Low-profile and discreet
- Amazing RF range
- Up to 1-inch magnet gap
- Support for an external contact
- Peel and stick installation
- 6+ year battery life
- 5-year warranty
- Water, high and low temp sensing
- Fast Install "Just toss in"
- Multiple applications
- IP67 waterproof
- 10 year nominal battery life
- Titanium probes for unmatched corrosion immunity
- IP67 rated waterproof enclosure
- GORE vent to prevent seal failure
- 5-year warranty
- Industry-leading wireless range and battery life
- One door window zone and two external contact zones
- Secure encrypted wireless transmissions
- 5-year warranty
- Dimensions: 23.97mm D x 39.91mm W x 79.60mm L
- Frequency: 319.5 MHz
- Battery: 3V lithium CR123A
- Magnet Gap: 1 inch max
- Operating Temperature: 32- 110F (0- 45C)
- Operating Humidity: 5 - 85% RH non-condensing
- Supervisory signal interval: 60 min (approximately)
- Potentiometer: Shock sensitivity adjustment
Optional plug-in module for connection to the Internet via a wireless (Wi-Fi) link, eliminating a wired Ethernet cable (for use w/ any StarLink Model)
The PG9905 Wireless PowerG Temperature Detector is used where temperature detection is critical. Early warning of potentially dangerous temperatures enables users to pre-emptively take action to resolve the situation. The PG9905 is designed to monitor the temperature of the area in which it is installed and communicate to the control system changes in temperature.
The PG9905 is ideal for residential and commercial installations where running wires is either difficult or impossible. The PG9905 is equipped with a visible signal quality LED indicator that lets the installer choose the optimal location for installation, eliminating the effort of going back and forth to the keypad.
The PG9905 can be used for both indoor and outdoor temperatures. When PG9905 monitors indoor temperature, it uses an internal sensor. When installed to monitor outdoor temperatures or refrigerator installations, the PG9905 uses an optional waterproof temperature probe. The temperature information communicated from the PG9905 to the control panel can also be displayed on the system keypad to provide status of indoor and outdoor temperature.
Features:
- Visible link quality indication shown on the device
- Programmable temperature warning and alarm thresholds
- Optional probe to monitor refrigerator, freezer and outdoor temperatures
- Front and back tamper protected
- Prolonged battery life (7 years with typical use)
- Dimensions: 81 x 32 x 25mm (3.19 x 1.25 x 1in)
- External temperature probe PGTEMP-PROBE
S2K Administration - Form Template Display
Actions