KEYPADS(NO RF),CTRL. MODULES

Compare

M1 16 Zone Input Expander

Adds 16 hardwired zones (EOL resistor supervised) to the M1 Gold or M1EZ8 Controls. Operates from 4-wire data bus. Up to 12 of these can be used, increasing total zones (inputs) to 208.
Includes:

16 Zone Input Expander

ELK-SWG Circuit Board Mounting Glides 2/pack

18 2200 Ohm Resistors

Instructions

Features:

16 EOL Resistor Supervised Hardwire Zones
Operates on the 4-Wire Data Bus
DIP Switch Address Settings
Flash Memory for Firmware Updating
Plug-In Terminal Strips
Status and Diagnostic LED
On-Board EOL Bus Termination Jumper
Vertical Mounting using ELK-SWG Glides(included)

Specifications:

Inputs: Plug-In Terminals with Elevator Style Wire Clamps and Screws
Operating Power Range: 9 to 14 VDC
Current Draw: 65 mA
Size: 6 in. x 3.25 in. x .75 in. H

Item#:

M1XIN

You must be logged in to order this item. Log in here

Compare

Touchpad Slimline Pro, Connect Family Encrypted, White

Item#:

RE667X-PRO

You must be logged in to order this item. Log in here

Compare

Small, economical, arm/disarm station for M1 Controls which fits into a single gang box and utilizes a standard decorator style faceplate (not included). Particularly well suited for partitioned jobs such as an office, workshop, garage, etc., but can also be used as the main keypad for any installation. Displays basic system status with 3 LEDs: Green "Ready", Yellow "Trouble", and Red "Armed". The 12 button keypad is backlit with blue LEDs and has quick arm keys for "EXIT" and "STAY". The M1KPAS also provides access to six (6) programmable function operations by pressing the "F" key followed by the number key (1-6) within 5 seconds.

Blue Backlit Keys
Quick Arm Exit & Stay Keys
LED Status Indication
Instant Activation of 6 Tasks
Operates from M1G or EZ8 "RS-485" Data Bus
Built-in Piezo Sounder
Connection: 4 Pin Plug-in "Flying Lead" Connector (Included)
Color: White
Operating Voltage: 13.8VDC

Item#:

M1KPAS

You must be logged in to order this item. Log in here

Compare

M1 LCD Low Profile Keypad

The ELK-M1KP2 is a low profile, addressable LCD Keypad for the M1 family of Cross Platform Controls®. It features a 32 character blue/white backlighted display, blue lighted keys, 4 programmable function keys, along with the ELK menu navigation keys. It may also be recess 'flush' mounted using with a separately purchased back box kit (ELK-M1BBK2). The M1KP2 is compatible with "external" 26 bit Wiegand compatible proximity readers, allowing cards or fobs to be used for arming, disarming, or limited door strike control, etc.
Includes:

Low Profile LCD Keypad with Blue Display

1 each Multicolor Labels

4 #6 Flat Head Phillips Sheet Metal Screw

4 #4-20 Pan Head Phillips Plastite Screw

1 2200 Ohm Resistor

5 Gel Filled B-Connector

1 Mini Jumper

6-wire Flying Lead Cable Assembly

Instructions

Features:

Blue/white Backlighted Hi-Contrast LCD Display
Four (4) Programmable Function Keys
Unique Menu Navigation/Direction Keys
Operates from the M1/EZ8 RS-485 Data Bus
Built-in Piezo Sounder with adjustable pitch
Accepts "External" 26 bit Wiegand Prox Reader (Optional)
Input for 1 Supervised Zone
One Programmable "Switched Positive" Voltage Output
Exit, Stay, Chime, and Bypass Keys
Surface mounts to a standard 1 or 2 gang electrical box
Optional recess 'flush' mount kit available (ELK-M1BBK2)

Specifications:

Connection: 6 Pin Plug-in "Flying Lead" Connector (Included)
Color: White
Operating Voltage: 13.8 VDC
Current Draw: ~30 mA Idle (low back light level, sounder silent) ~85mA Fully Active (max. back light & sounder active)
Size: 4.658 in. W x 5.5 in. H x .95 in. D (.375 in. D with recess mount)

Item#:

M1KP2

You must be logged in to order this item. Log in here

Compare

Ethernet Port Interface

The ELK-M1XEP is an Ethernet Appliance with a RS-232 Serial Port Interface. It may be used to connect a control in the M1 Family to an Ethernet network. It features email event notification and FIPS compliant encryption algorithms for security sensitive environments. It is powered by an ELK-P1216 12 Volts DC, 1.5 Amp plug-in power supply/adapter. A software setup utility is built into ElkRP for configuring the connection setup, network password, etc. The M1 Ethernet Interface is factory defaulted to obtain a dynamic IP address from a DHCP server (i.e. router, cable modem, etc.). It may optionally be setup with a static IP address.
Includes:

M1 Ethernet Interface

Plastic Housing

4 #6 Plastic Anchors

4 #6 Pan Head Sheet Metal Screws

ELK-P1216 1.6A, 12Vdc Power Supply

ELK-W040A DB9 Pin Serial Cable Assembly

Instructions

Features:

Secure connection with password protection and SSL/TLS encryption
Flash Memory for Firmware Updating
Event notification via E-Mail (SMTP)
Supports automatic Dynamic DNS Updates with providers using the DynDNS protocol.
Supports Network Time Protocol for synchronizing the M1/EZ8's clock with an Internet time server.
Internet Monitoring and Reporting Capability
Network stack supporting the following protocols:
- TCP,UDP,DHCP,SSL/TLS, NTP, SMTP
Federal Information Processing Standards (FIPS) 128 bit encryption
Integrated 802.3 compliant 10/100 Mbit network interface
RS232, DB9M 9-pin serial port connection
Connects to the M1 RS-232 Serial port (Port 0). The baud rate for this port must be set to 115,200 (factory default)
RJ45 8-pin Network Jack
2.1mm barrel type power connector (center positive)
LED Indicators for Power, Link, and Data

Specifications:

Operating Voltage: 12 Volts D.C. from Elk-P1216 Plug-in Power Supply **
Current Draw: approx. 300 mA
Housing Dimensions: 4.25 in. x 6.375 in. x 2.125 in.
Circuit Board Dimensions: 2.25 in. x 3.95 in.
ELK-W040A Serial Ribbon Cable included

Item#:

M1XEP

You must be logged in to order this item. Log in here