S2K Commerce - Products Dropdown
ActionsS2K Commerce - Shopping Cart
ActionsS2K Commerce - Order Entry
ActionsThe PG9920 PowerG Wireless Repeater significantly extends the communication range between the alarm system and other PowerG devices where the size of the building, layout or even materials of construction, require additional coverage.
When messages from the wireless PowerG devices are received, the PG9920 forwards these messages to the control panel.
The PG9920 continuously measures communication quality and automatically sets transmission power to the minimum required for reliable communication.
With minimal installation time required and few holes to drill, the PG9920 Wireless Repeater reduces on-site time and increases productivity and revenue. The PG9920 is equipped with a visible signal quality LED indicator that lets the installer choose the optimal location for installation, eliminating the effort of going back and forth to the keypad.
Features:
- Extends the overall wireless range
- LED indications for power failure, activity and installation performance diagnostics
- Compact and easy to install
- Front and back tamper protected
- Mains powered with 48 hour backup battery (rechargeable)
- Dimensions: 161 x 161 x 50mm (6.44 x 6.445 x 1.74in)
The Inovonics 16 zone multi-condition receiver with relay outputs programs and supervises up to 16 single or multiple condition transmitters. This receiver includes Form C relays for each output, allowing connection to any hardwire panel, or stand-alone wireless application.
Features:
- Add up to 16 high performance EchoStream wireless transmitters to any installation
- Includes support for both single and multiple condition transmitters
- Two line text display shows condition of each transmitter, provides log of past events, and displays signal strength
- Six form C relays for connecting to any panel
- Outputs can be configured in follower, latching, momentary, or toggle modes independently
- Case tamper protection, jam detection, and internal antennas for a secure wireless implementation
- Wireless programming routine built into the receiver
Adds 16 hardwired zones (EOL resistor supervised) to the M1 Gold or M1EZ8 Controls. Operates from 4-wire data bus. Up to 12 of these can be used, increasing total zones (inputs) to 208.
Includes:
- 16 Zone Input Expander
- ELK-SWG Circuit Board Mounting Glides 2/pack
- 18 2200 Ohm Resistors
- Instructions
- 16 EOL Resistor Supervised Hardwire Zones
- Operates on the 4-Wire Data Bus
- DIP Switch Address Settings
- Flash Memory for Firmware Updating
- Plug-In Terminal Strips
- Status and Diagnostic LED
- On-Board EOL Bus Termination Jumper
- Vertical Mounting using ELK-SWG Glides(included)
- Inputs: Plug-In Terminals with Elevator Style Wire Clamps and Screws
- Operating Power Range: 9 to 14 VDC
- Current Draw: 65 mA
- Size: 6 in. x 3.25 in. x .75 in. H
Features:
- Compatible with any hardwired sensors going to the various wireless panels
- 8 Hardwire loops with end-of-line resistor detection
- Unique wireless ID (or loop) for each zone
- Unique wireless ID for the device itself
- Transmit diversity for long reliable range
- PIR powering (via external supply)
- Device low battery detect
- Device tamper detect
- External 12VDC power supply required (sold separately
- Isolate open and short circuit faults from main V-Plex loop
- Provides additional V-Plex loop current
- V-Plex loop isolation between primary and extended loop
- Fully supervised
- Separate DC input, no current drain from primary V-Plex loop
- Monitors DC power input
The 2GIG 345MHz Repeater is designed to work with 2GIG security systems providing more flexibility in where wireless sensors can be installed. The 2GIG Repeater can be installed in the optimal location to extend the range of 2GIG panels for large jobs. The 2GIG 345MHz Repeater will repeat 2GIG and Honeywell sensor signals to 2GIG panels. The Repeater is a plug and play device that will immediately start repeating signals when powered on. The rechargeable battery provides backup power in case of AC power loss.
Features:
- Converts hardwired loops into as many as 8 wireless zones
- Converts 8 zones per module (additional modules may be added)
- Operates at 9-16 VDC, 50 mA
- Can be powered by and use backup battery of an existing 3rd party Control Panel
- ETL Listed
The Super Switch is 2GIGs wireless takeover module. This unit was designed to convert 8 hardwired zones into eight wireless zones, make installation simple, and work with existing 12volt control panels. The module is to be mounted next to the existing Control Panel where the hardwired zones are connected. All of the zones on the Super Switch act as supervised wireless zones.
Features:
It will repeat 2GIG and Honeywell sensor signals to 2GIG panels
Features
- Repeats 2GIG and Honeywell signals on 345MHz frequency
- 24-hour backup battery included
- Repeat indicator in the signal eliminates “repeated signal storm”
- Optional zone programming to supervise Tamper, AC Loss, and Low Battery
The ELK-M1XSLU is a dedicated Elk-M1 serial expander for connecting an M1 Control to a Lutron RadioRA2 Main Repeater. RadioRA2 is a wireless multi-room control system for Lights, Shades, and HVAC Thermostats. Interfacing a RadioRA2 system to an M1 allows control in response to security system actions or conditions. With the automation and remote capabilities built into M1 it is possible to control RadioRA2 devices from across the room or across the world. Benefits include energy savings, convenience, and comfort.
The M1XSLU should be mounted as close as possible to the RadioRA2 Main Repeater. An 18 inch 9-pin flat ribbon serial interconnect cable is provided.
Includes:
- M1 to Lutron RadioRA2 Serial Interface
- Plastic Housing
- ELK-W040A DB9 Pin Serial Cable Assembly
- 4 #6 Plastic Anchors
- 4 #6 Pan Head Sheet Metal Screws
- Instructions
- Activity/Status LED (Orange)
- Auto-Reset Hardware Watchdog Circuit
- Addressable (1-7) TYPE 5 Databus ID
- Connection to Main Repeater: RS232 Cable - Included
- Connection to M1: Elevator Screw Terminals (4)
- Operating Voltage: 12 Volts D.C.
- Current Draw: 31mA
- Housing Dimensions: 4.25 in. x 6.375 in. x 2.125 in.
- Circuit Board: 2.75 in. x 3.95 in.
- Adds up to 144 individual wireless zones (sensors/points)
- Operates from the 4 wire M1 RS485 Data Bus
- Additional Receivers (up to 11) may be connected to a single M1 or M1EZ8 Control for redundancy or greater coverage
- Flash Memory for Updating of operating Firmware
- Sensitivity: >105 dbm
- Operating Temperature: 0 to 120 degrees F
- Operating Voltage: 12 Volts D.C.
- Current Draw: 70mA
- Indoor Range: 300 to 500 ft. line of sight